![]() ![]() Set up travel restraint or fall arrest systems for those persons working in the fall hazard area while the toeboard is not in place or cannot be relied upon.Post warning signs outside the roped off area alerting workers of the danger from the unprotected fall hazard.Alert all those working nearby that the guardrails are no longer adequate protection.Mark it off as a fall hazard area with caution tape or a warning barrier.Clear that area so it is free from slip or trip hazards. ![]() To ensure the safety of those around the fall hazard area: When work on a guardrail requires removing a toeboard or the toeboard is in poor condition, consider the whole guardrail system as unsafe and the fall hazard area as unprotected. What should be done if the toeboard is removed or in poor repair? Back to top Improper removal of toeboards can leave protruding edges or parts, such as nails, that may injure workers. When installing or rebuilding a toeboard, make sure it is installed according to the manufacturer's instructions, or your jurisdiction's requirements. Ladders are drilled on both sides and Outriggers are interchangeable for. Guardrails are required when the working height of a scaffold is 10ft or greater. Guardrail and Toe Board kits provide additional safety and are sold separately. Panels may be required when stacking material near a fall area, such as an elevated walkway or floor opening. The Werner SRG-72 is a Guardrail and Toeboard Kit for the SRS-72 Steel Rolling Scaffold. Regulations will often specify toeboard requirementsm In general, the toeboard is not high enough (or too high) to prevent tools or items from falling, increase the height of the toeboard, or install solid or mesh panels. What should be considered when installing and removing toeboards? Back to top Always check with your jurisdiction for exact requirements. In most jurisdictions, use of a toeboard may be specified for certain circumstances, particularly when used with guardrails. ![]() The CSA Standard Z797-18 Code of practice for access scaffold also provides minimum load bearing and height requirements for guardrails and toeboards. The force requirements will depend on the applications of the guardrail, toeboards and the legislative requirements in your jurisdiction. This requirement refers to the amount of force that guardrails and toeboards may be expected to support, and is measured in newtons (N) or pounds (lbs). Regulations often require a load specification. What is meant by load specifications? Back to top See the OSH Answers documents for more information on guardrails, as well as fall protection. other unprotected edges at a height where materials could fall off the edge.It is good practice to have toeboards around As well, toeboards alert workers to an edge, providing added protection to help prevent individuals from slipping over the edge. They are often used as a part of a guardrail system. They are often used when there is a risk that tools or other objects could fall onto a person from a platform or other raised area, or through a floor opening or hole. Nu-Wave Guardrail Kit Complete for 4ft Scaffold GKC-4. Toeboards are protective barriers that are placed near the ground or walking surface. Save today on the Nu-Wave Guardrail Kit Complete for 4ft Scaffold from. Fits 43" Ladder sectionsĥ Rung End Frame access Ladder.You are here: Fall Protection - Toeboards Set Of 4 20" Outriggers Without Casters For Use When Stacking Unitsģ Rung End Frame access Ladder. Single 20" Outrigger Without Caster For Left Side Of Scaffold Works with all non import Perry Scaffolds ![]() Single 20" Outrigger Without Caster For Right Side Of Scaffold Super Pro Lock Complete With Hand Rails and Mini Stabilizers *Platform heights are adjustable in 4" increments from just a few inches off the floor to a maximum standing height of 6 ft.Ĭomplete Perry scaffold with 5" Base PlatesĬomplete Perry scaffold with 5 inch PC5BS castersĬomplete Perry Scaffold with PIC5 CastersĬomplete Perry scaffold with 5 inch PC5BS caster *5 basic components: 2 end frame access ladders, 2 adjustable platform-support trusses, 1 platform *Platform Heights are adjustable by 1 person in seconds-without tools *1 Person can assemble a basic section in less than a minute without tools Stackable up to 3 units high with use of outriggers. Available in 4, 6, 8, or 10 foot lengths, all 29.5" wide. The Perry Scaffold features 5” casters for stability and ease of movement. The original Perry Scaffold features a patented Positive Engagement Locking System for fast easy assembly. Eastern.7 Days A Week!Īll of our Perry Scaffolding is Brand New! ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |